www.pridemobility.com Owner's ManualPage 2 Jazzy 1113 ATS S A F E T Y G U I D E L I N E S Copyright ©2002 Pride Mobility Products Corp.Please read and follow all instructions in this owner’s manual before attempting to operate your power chair for the first time. If there is anything in this manual you do not understand,or if you require additional assistance for set-up,contact your authorized Pride provider.Using your Pride Power Chair safely depends upon your diligence in following the warnings,cautions,and instructions in this owner’s manual. Using your Pride Power Chair safely also depends upon your own good judgement and/or common sense,as well as that of your provider,caregiver,and/or healthcare professional. Pride is not responsible for injuries and/or damage resulting from any person’s failure to follow the warnings,cautions,and instructions in this owner’s manual. Pride is not responsible for injuries and/or damage resulting from any person’s failure to exercise good judgement and/or common sense.The symbols below are used throughout this owner’s manual to identify warnings and cautions. It is very important for you to read and understand them completely.WARNING! Failure to heed the warnings in this owner’s manual may result in personal injury.CAUTION! Failure to heed the cautions in this owner’s manual may result in damage to your power chair.2 INFMANU1801/REV F/JULY 2002Page 3 3Jazzy 1113 ATS C O N T E N T S I.INTRODUCTION 4 II. SAFETY . 6 III. EMI/RFI 14 IV. YOUR JAZZY 1113 ATS 16 V.DISASSEMBLY . 21 VI. COMFORT ADJUSTMENTS 24 VII. ASSEMBLY. 28 VIII.OPERATION. 30 IX. BATTERIES AND CHARGING . 32 X. CARE AND MAINTENANCE . 36 XI. OPTIONAL ACCESSORIES. 42 XII. WARRANTY 44Page 4 4Jazzy 1113 ATS I . I N T R O D U C T I O N Welcome to Pride Mobility Products Corporation (Pride). Congratulations on the purchase of your new Jazzy Power Chair. The Jazzy 1113 ATS design combines the most advanced state-of-the-art components with modern,attractive styling. We are certain that the design features and trouble-free operation of your new Jazzy Power Chair will add convenience to your daily living.At Pride,your safety is important to us.Please read and follow all of the instructions in this manual before you attempt to operate your Jazzy for the first time.These instructions were produced for your benefit. Your understanding of these instructions is essential for the safe operation of your new Jazzy Power Chair.Pride is not liable for damage to property or personal injury arising out of unsafe use of a Jazzy Power Chair. Pride is also not liable for any property damage or personal injury arising out of the failure of any person and or/user to follow the instructions and recommendations set forth in this manual or any other instructions or recommendations contained in other Jazzy related literature issued by Pride or contained on the Jazzy Power Chair.This owner’s manual is compiled from the latest specifications and product information available at the time of publication. We reserve the right to make changes as they become necessary. Any changes to our products may cause slight variations between the illustrations and explanations in this manual and the product you have purchased.If you experience any problems with your Jazzy that your are unable to solve,or if you do not feel capable of safely following any of the instructions and/or recommendations as contained in this manual,please contact your authorized Pride provider for assistance.Once you understand how to operate and take care of your Jazzy,we are certain that it will give you years of trouble-free service and enjoyment.Information Exchange We want to hear your questions,comments,and suggestions about this manual. We would also like to hear about the safety and reliability of your new Jazzy Power Chair,and about the service you received from your authorized Pride provider.Please notify us of any change of address,so we can keep you apprised of important information about safety,new products,and new options that can increase your ability to use and enjoy your Jazzy. Please feel free to write us at the address below: Pride Mobility Products Corporation Attn: Customer Care Department 182 Susquehanna Avenue Exeter,PA 18643-2694 customercare@pridemobility.comPage 5 5Jazzy 1113 ATS I . I N T R O D U C T I O N Pride Owners Club As an owner of a Pride product,you are invited to register your product’s warranty and enroll in the Pride Owners Club. You may do so by filling out and returning your enclosed registration card or by visiting Pride’s web site at www.pridemobility.com . As a registered member,each time you visit our site,you will have access to the most interactive and honest educational website available today for people with mobility needs,their families and friends.From our home page,select the “Owners Club” link to enter a page dedicated to current and potential Pride product owners. You will gain access to interviews,stories,recreation ideas,daily living tips,product and funding information,and interactive message boards. On these message boards you are invited to speak with other Pride customers as well as Pride representatives who are available to assist you with any questions or concerns you may have. You will receive a free gift simply for registering with the Pride Owners Club.My Authorized Pride Provider is: Name: Address: Phone Number: Quick Reference Information: Jazzy Model: Serial Number: Purchase Date: NOTE:If you ever lose or misplace your warranty card or your copy of this manual,email or write to us and we will be glad to send you a new one immediately.Page 6 6Jazzy 1113 ATS I I . S A F E T Y GENERAL WARNING! Do not operate your new power chair for the first time without completely reading and understanding this owner’s manual.Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the power chair user. Please be aware that the final selection and purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user,who is capable of making such a decision,and his/her healthcare professional (i.e.,medical doctor,physical therapist,etc.).The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair to the user and has assisted the prescribing healthcare professional and/or the authorized Pride provider in the instruction process for the use of the product.There are certain situations,including some medical conditions,wherein the power chair user will need to practice operating the power chair in the presence of a trained attendant. A trained attendant can be defined as a family member or care professional specially trained in assisting a power chair user in various daily living activities.As you begin using your power chair during daily activities,you will probably encounter situations in which you will need some practice. Simply take your time and you will soon be in full and confident control as you maneuver through doorways,on and off of elevators,up and down ramps,and over moderate terrain.Below are some precautions,tips,and other safety considerations that will help the user become accustomed to operating the power chair safely.MODIFICATIONS Pride has designed and engineered your power chair to provide maximum mobility and utility. A wide range of accessories is available from your Pride provider to further customize your power chair to better suit your needs and/or preferences. However,under no circumstances should you modify,add,remove,or disable any feature,part,or function of your power chair.WARNING! Do not modify your power chair in any way not authorized by Pride. Unauthorized modifications may result in personal injury and/or damage to your power chair.PRE-RIDE SAFETY CHECK Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check before each use to make sure your power chair operates smoothly and safely. See X. “Care and Maintenance.”Page 7 7Jazzy 1113 ATS I I . S A F E T Y Perform the following inspections prior to using your power chair: n Check for proper tire inflation. Maintain 30-35 psi in each tire (if equipped with pneumatic tires).n Check all electrical connections. Make sure they are tight and not corroded.n Check all controller connections to the utility tray. Make sure they are secured properly.n Check the brakes. See X. “Care and Maintenance.” n Check battery charge. See IX. “Batteries and Charging.” If you discover a problem,contact your authorized Pride provider for assistance.WEIGHT LIMITATIONS Your power chair is rated for a maximum 250-lb. weight limit.WARNING! Exceeding the weight limit voids your warranty and may result in personal injury and/ or damage to your power chair. Pride will not be held responsible for injuries and/or property damage resulting from failure to observe weight limitations.WARNING! Do not carry passengers on your power chair. Carrying passengers on your power chair may result in personal injury and/or property damage.TIRE INFLATION If your power chair is equipped with pneumatic tires,you should check or have the air pressure checked at least once a week. Proper inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.WARNING! It is important that 30-35 psi tire pressure be maintained in pneumatic tires at all times.Failure to maintain 30-35 psi tire pressure in pneumatic tires at all times may result in tire and/or wheel failure,causing serious personal injury and/or damage to your power chair.WARNING! Make sure your tires are inflated to 30-35 psi. Do not underinflate or overinflate your tires. Low pressure may result in loss of control,and overinflated tires may burst. Serious personal injury may result.WARNING! Inflate your power chair drive tires from a regulated air source with an available pressure gauge. Minimum air pressure for power chair drive tires is 30-35 psi. Inflating your tires from an unregulated air source could overinflate them,resulting in a burst tire and/or personal injury.INCLINE INFORMATION More and more buildings have ramps with specified degrees of inclination,designed for easy and safe access. Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your power chair.n Proceed with extreme caution as you approach the downgrade of a ramp or other incline.n Take wide swings with your power chair’s front wheel(s) around any tight corners. If you do that,the power chair’s rear wheels will follow a wide arc,not cut the corner short,and not bump into or get hung up on any railing corners.Page 8 8Jazzy 1113 ATS n When driving down a ramp,keep the power chair’s speed adjustment set to the slowest speed setting to ensure a safely controlled descent. See VIII. “Operation.” n Avoid sudden stops and starts.When climbing an incline,try to keep your power chair moving. If you must stop,start up again slowly and then accelerate cautiously. When driving down an incline,do so by setting the controller at the slowest setting and driving in the forward direction only. If your power chair starts to move down the incline faster than you anticipated or desired,allow it to come to a complete stop by releasing the joystick,then push the joystick forward slightly to ensure a safely controlled descent.WARNING! When climbing an incline,do not zigzag or drive at an angle up the face of the incline.Drive your power chair straight up the incline. This greatly reduces the possibility of a tip or a fall.Always exercise extreme caution when negotiating an incline.WARNING! You should not travel up or down a potentially hazardous incline (i.e.,areas covered with snow,ice,cut grass,or wet leaves).WARNING! When on any sort of an incline or decline,never place the power chair in freewheel mode while seated on it or standing next to it. Doing so may result in personal injury and/or damage to your power chair.In compliance with the Americans with Disabilities Act of 1990,all handicap public access ramps are required to have a maximum slope of 5°. Therefore,Pride recommends that the maximum slope of an incline you attempt to safely ascend or descend on your power chair does not exceed 5°.WARNING! Any attempt to climb or descend a slope steeper than five degrees may put your power chair in an unstable position and cause it to tip,resulting in personal injury.BRAKING INFORMATION Your power chair is equipped with two powerful brake systems: 1. Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.2. Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop,or when power is removed from the system for any reason.Figure 1. Maximum Incline Angle I I . S A F E T YPage 9 9Jazzy 1113 ATS CORNERING INFORMATION While your power chair is equipped with rear caster wheels in back and anti-tip wheels in front,excessively high cornering speeds can still create the possibility of tipping. Factors which affect the possibility of tipping include,but are not limited to,cornering speed,steering angle (how sharply you are turning),uneven road surfaces,inclined road surfaces,riding from an area of low traction to an area of high traction (such as passing from a grassy area to a paved area – especially at high speed while turning),and abrupt directional changes. High cornering speeds are not recommended. If you feel that you may tip over in a corner,reduce your speed and steering angle (i.e. lessen the sharpness of the turn) to prevent your power chair from tipping.WARNING! When cornering sharply,reduce your speed. This greatly reduces the possibility of a tip or fall. To avoid personal injury and/or property damage,always exercise common sense when cornering.OUTDOOR DRIVING SURFACES Your power chair is designed to provide optimum stability under normal driving conditions—dry,level surfaces composed of concrete,blacktop,or asphalt. However,Pride recognizes that there will be times when you will encounter other surface types. For this reason,your power chair is designed to perform admirably on packed soil,grass,and gravel. Feel free to use your power chair safely on lawns and in park areas.n Reduce your power chair’s speed when driving on uneven terrain and/or soft surfaces.n Avoid tall grass that can entangle the running gear.n Avoid loosely packed gravel and sand.n If you feel unsure about a driving surface,avoid that surface.I I . S A F E T YPage 10 10 Jazzy 1113 ATS I I . S A F E T Y FREEWHEEL MODE Your power chair is equipped with a freewheel lever to allow for manual maneuverability by a trained attendant. For more information about how to place your power chair into and out of freewheel mode,see IV. “Your Jazzy 1113 ATS.” WARNING! Do not use your power chair in freewheel mode without the presence of an attendant.Personal injury may result.WARNING! Do not attempt to personally place your power chair in freewheel mode while seated on it. Personal injury may result. Ask an attendant for assistance if necessary.WARNING! Do not place your power chair in freewheel mode while on an incline. The chair could roll uncontrollably on its own,causing personal injury.STATIONARY OBSTACLES (STEPS,CURBS,ETC.) Proceed with extreme caution when driving near raised surfaces,unprotected ledges and/or drop-offs (curbs,porches,stairs,etc.).WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher than two inches unless you have the assistance of an attendant.WARNING! Do not attempt to have your power chair proceed backward down any step,curb,or other obstacle. This may cause the power chair to tip and cause personal injury.PUBLIC ROADS AND PARKING LOTS WARNING! You should not operate your power chair on public streets and roadways. Be aware that it may be difficult for traffic to see you when you are seated on your power chair. Obey all local pedestrian traffic rules. Wait until your path is clear of traffic,and then proceed with extreme caution.STAIRS AND ESCALATORS Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator.WARNING! Never use your power chair to negotiate steps or escalators. You may cause injury to yourself and to others and/or damage your power chair.DOORS n Determine if the door opens toward or away from you.n Use your hand to turn the knob or push the handle or push-bar.n Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently and slowly backward to pull the door open.Page 11 11 Jazzy 1113 ATS ELEVATORS Modern elevators have a door edge safety mechanism that,when pushed,reopens the elevator door(s).n If you are in the doorway of an elevator when the door(s) begin to close,push on the rubber door edge or allow the rubber door edge to contact the power chair and the door will reopen.n Use care that pocketbooks,packages,or power chair accessories do not become caught in elevator doors.ELECTROMAGNETIC & RADIO FREQUENCY INTERFERENCE (EMI & RFI) Laboratory tests performed by the Food and Drug Administration (FDA) have shown that radio waves can cause unintended motion of electric mobility vehicles. Radio waves are a form of electromagnetic energy (EM). When EM adversely affects the operation of an electronic device,it is called Electromagnetic Interference (EMI) or Radio Frequency Interference (RFI). For more information,see III. “EMI/RFI.” LIFT/ELEVATION PRODUCTS If you will be traveling with your power chair,you may find it necessary to use a lift/elevation product to aid in transportation. Pride recommends that you closely review the instructions,specifications,and safety information set forth by the manufacturer of the lift/elevation product before using that product.MOTOR VEHICLE TRANSPORT Currently,there are no standards approved for tie-down systems in a moving vehicle of any type to transport a person while seated in a power chair.TRANSFERS Transferring onto and off of your power chair requires a good sense of balance. Always have an attendant or healthcare professional present while learning to properly transfer yourself.To eliminate the possibility of injury,Pride recommends that you or a trained attendant perform the following tasks before attempting a transfer: n Turn the power off. See VIII. “Operation.” n Ensure your power chair is not in freewheel mode. See IV. “Your Jazzy 1113 ATS.” n Make sure the armrests are flipped up or removed from your power chair.n Flip the footrest up,or move the leg rests aside; this will help to keep your feet from getting caught on the footrest or the leg rests during the transfer.n Reduce the distance between your power chair and the object you are transferring onto.n Turn both rear caster wheels toward the transfer destination to improve power chair stability during transfer.WARNING! Before transferring,position yourself as far back as possible in the power chair seat to prevent the power chair from tipping forward during transfer and causing injury.WARNING! Avoid using your armrests for weight bearing purposes. Such use may cause the power chair to tip and cause personal injury.WARNING! Avoid putting all of your weight on the footrest. Such use may cause the power chair to tip and cause personal injury.I I . S A F E T YPage 12 12 Jazzy 1113 ATS Although your power chair may be equipped with a positioning belt,this belt is not designed to provide proper restraint during motor vehicle transport. Anyone traveling in a motor vehicle should be properly secured in the motor vehicle seat with safety belts securely fastened.WARNING! Do not sit on your power chair while it is in a moving vehicle. Personal injury and/or property damage may result.WARNING! Always be sure your power chair and its batteries are properly secured when it is being transported. Failure to do so may result in personal injury and/or damage to your power chair.POSITIONING BELTS Your authorized Pride provider,therapist(s),and other healthcare professionals are responsible for determining your requirement for a positioning belt in order to operate your power chair safely.WARNING! If you require a positioning belt to safely operate your power chair,make sure it is fastened securely. Serious personal injury may result if you fall from the power chair.INCLEMENT WEATHER PRECAUTIONS WARNING! Pride recommends that you do not operate your power chair in icy or slippery conditions or on salted surfaces (i.e.,walks or roads). Such use may adversely affect the performance and safety of your power chair,resulting in an accident and personal injury.WARNING! Do not expose your power chair to any type of moisture at any time (rain,snow,mist,or wash). Such exposure can damage your power chair. Never operate your power chair if it has been exposed to moisture until it has dried thoroughly.REACHING AND BENDING Never reach,lean,or bend while driving your power chair. If it is absolutely necessary to reach,lean,or bend while seated on your power chair,it is important to maintain a stable center of gravity and keep the power chair from tipping. Pride recommends that the power chair user determine his/her personal limitations and practice bending and reaching in the presence of a qualified heatlthcare professional.WARNING! Do not bend,lean,or reach for objects if you have to pick them up from the floor by reaching down between your knees. Movements such as these may change your center of gravity and the weight distribution of the power chair. This may cause your power chair to tip,possibly resulting in personal injury. Keep your hands away from the tires when driving.I I . S A F E T YPage 13 13 Jazzy 1113 ATS BATTERIES In addition to following the warnings below,be sure to comply with all other battery handling information.For more information about your power chair’s batteries,see IX. “Batteries and Charging.” WARNING! Power chair batteries weigh approximately 24 pounds each. If you are unable to lift that much weight,be sure to get help. Lifting beyond your capacity can result in personal injury.WARNING! Battery posts,terminals,and related accessories contain lead and lead compounds.Wash hands after handling.WARNING! Always protect the batteries from freezing and never charge a frozen battery. Charging a frozen battery may result in personal injury and/or damage to the battery.PREVENTING UNINTENDED MOVEMENT WARNING! If you anticipate being seated in a stationary position for an extended period of time,turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This will also eliminate the possibility of unintended chair movement from electromagnetic (EM) sources. Failure to do so may result in personal injury.PRESCRIPTION DRUGS/PHYSICAL LIMITATIONS Users must exercise care and common sense when operating a power chair. This includes awareness of safety issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations.WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or if you have certain physical limitations. Some medications and limitations may impair your ability to operate your power chair in a safe manner.ALCOHOL The power chair user must exercise care and common sense when operating his/her power chair. This includes awareness of safety issues while under the influence of alcohol.WARNING! Do not operate your power chair while you are under the influence of alcohol,as this may impair your ability to operate your power chair in a safe manner.REMOVABLE PARTS WARNING! Do not attempt to lift or move a power chair by any of its removable parts. Personal injury and/or damage to the power chair may result.I I . S A F E T YPage 14 14 Jazzy 1113 ATS I I I . E M I / R F I EMI/RFI WARNINGS Laboratory tests performed by the Food and Drug Administration (FDA) have shown that radio waves can cause unintended motion of electric mobility vehicles. Radio waves are a form of electromagnetic energy (EM). When this energy unintentionally affects the operation of an electronic device,it is called Electromagnetic Interference (EMI) or Radio Frequency Interference (RFI) .FREQUENTLY ASKED QUESTIONS (FAQS) The following FAQs summarize what you should know about EMI/RFI. Use this information to minimize the risk that EMI/RFI may affect your power chair.Where do radio waves come from?Radio waves are emitted from the antennas of cellular phones,mobile two-way radios,walkie-talkies,radio stations,TV stations,amateur radio (HAM) transmitters,wireless computer links,microwave sources,and paging transmitters. Radio waves are a form of electromagnetic energy (EM). EM is more intense closer to transmitting antennas,which are sources of emission. The greater the transmission strength,the greater the concern to electric mobility vehicle users.If my power chair is affected by EMI/RFI,what kind of motion should I expect?This is hard to predict. The effect may depend on a number of factors including: n Strength of the radio waves n Construction of the electric mobility vehicle n Position of the power chair (whether it is on level ground or on a slope) n Whether or not the electric mobility vehicle is in motion Electric mobility vehicle motion caused by EMI/RFI can be erratic. The vehicle may move by itself or come to a sudden stop. Furthermore,it is possible for EMI/RFI to unexpectedly release the brakes on an electric mobility vehicle. Some intense sources of EMI/RFI can even damage the control system of an electric mobility vehicle.Is there any way to know for sure whether radio waves are responsible for the unintended motion of my power chair?Unfortunately,interference from radio wave sources may be difficult to recognize,because the signals from these sources are invisible and may be intermittent. However,the FDA recommends that you report all incidents of unintended motion or brake release to the electric mobility vehicle manufacturer and,if possible,note whether there was a radio wave source nearby at the time of the incident.Has anyone been hurt from erratic,unintended motion of electric mobility vehicles?The FDA has reports of injuries that may have resulted from the uncontrolled motion of electric mobility vehicles. However,it is unclear how many of these incidents were actually caused by radio wave interference.Are all electric mobility vehicles susceptible to EMI/RFI?Each make and model differs in its ability to resist EMI/RFI. Each electric mobility vehicle has a particular level of immunity to EMI/RFI. This immunity level is measured in volts per meter (V/m). A higher immunity level offers greater protection. In other words,a power chair with a high immunity level is less likely to be affected by a strong radio source than one with a low immunity level.Page 15 15 Jazzy 1113 ATS I I I . E M I / R F I What is the FDA doing about the problem?The FDA has written to electric mobility vehicle manufacturers and has requested that they test their new products to be sure that they provide a reasonable degree of immunity against EMI/RFI. The letter states that electric mobility vehicles should have an immunity level of at least 20 V/m. This provides a reasonable degree of protection against common sources of EMI/RFI.The FDA has also requested or recommended that: n Electric mobility vehicle manufacturers clearly label new products with their immunity level,or state that the immunity level is not known.n The labeling or informational material supplied with new electric mobility vehicles must explain what the immunity level means and warn users about the possibility of EMI/RFI and how to avoid it.n Electric mobility vehicle manufacturers undertake an educational program to inform users and their caregivers about the problems associated with EMI/RFI and about the actions they can take to minimize the risk of EMI/RFI.n While there is no exact way to tell if your electric mobility vehicle is totally safe from EMI/RFI,an immunity level of 20 V/m is generally achievable and useful. Your power chair has been tested and passed at an immunity level of 20 V/m.What can I do to find out if my power chair is likely to be affected by EMI/RFI?If you have owned your power chair for a long time and have not experienced unintended motion,it is unlikely that you will have problems in the future. However,it is always possible that problems could arise if your power chair is close to a source of radio waves. Therefore,it is very important to be alert to this possibility. Your power chair meets or exceeds an immunity level of at least 20 V/m.What can I do to reduce the risk that my power chair could be affected by EMI/RFI?Here are some precautions you can take: n Do not turn on or use hand-held personal communications devices,such as citizens band (CB) radios and cellular phones,while the power chair is on.n Be aware of nearby transmitters such as radio or TV stations and hand-held or mobile two-way radios,and try not to come close to them. For example,if you are in a power chair with an immunity level of 20 V/m,you should remain at least three feet from a hand-held two-way radio and ten feet from a mobile two-way radio.n Be aware that adding accessories and/or components or modifying the power chair may make it more susceptible to interference from radio wave sources.n There is no easy way to evaluate the effect of accessories or modifications upon the overall immunity of the power chair.Page 16 16 Jazzy 1113 ATS I V . Y O U R J A Z Z Y 1 1 1 3 A T S Figure 2. The Jazzy 1113 ATS SEAT BACK ANTI-TIP WHEELS ARMRESTS BODY SHROUD FOOTREST CASTER WHEEL DRIVE WHEEL SEAT FRAME SEAT RELEASE PLUNGERS CONTROLLER POWER BASE ASSEMBLY SEAT ASSEMBLY FREEWHEEL LEVERS Your Jazzy has two main assemblies: the seat and the power base. See figure 2. There are a variety of seating options that are designed to accommodate most users. Typically,the seating system includes the armrests,the seatback,the seat base,and the joystick/controller. The power base is the heart of the Jazzy 1113 ATS. The power base assembly includes two drive wheels,two anti-tip wheels,two rear caster wheels,four frame assemblies,two battery boxes,and the electrical connectors. See figures 2,3,and 7. Your Jazzy seat may also have some optional accessories attached to it such as a basket,a cane/crutch holder,a cup holder,or a power seat switch. This information is included with the accessory.OFF-BOARD CHARGER PORT JOYSTICK SEAT BASEPage 17 17 Jazzy 1113 ATS I V . Y O U R J A Z Z Y 1 1 1 3 A T S Specifications Suspension: Active Trac System Drive Wheels: 10 in.,pneumatic (solid tires are optional) Caster Wheels: 8 in.,rear articulating Anti-tip Wheels: 6 in.,front mounted Max. Speed: 3 mph Ground Clearance: 1.75 in.Length Footplate Up: 33 in.Length Footplate Down: 39.5 in.Overall Width: 23 in.Turning Radius: 20.5 in.Seating Options: Medium Back High Back with Headrest Recliner Versa Seat/Versa Tilt Drivetrain: Two motor,mid-wheel Battery: 12-volt,U-1 (2) Battery Charger: 4-amp onboard (off-board optional) Per-Charge Range: Up to 25 miles Electronics: 50 amp P&G Pilot Weight Capacity: 250 lbs.Seat Weight: 36 lbs.Footrest Weight: 6.5 lbs.Front Battery and Case Weights: 25.5 lbs.Rear Battery and Case Weights: 25.5 lbs.Battery Well Frame Weight: 12.5 lbs.Front Frame Weight: 2.5 lbs.Right Frame Assembly Weight: 38 lbs.Left Frame Assembly Weight: 38 lbs.Total Weight: 185 lbs.Warranty: Lifetime Limited Warranty on Frame 2-year Limited Electronics Warranty 18 Months on Drive MotorsPage 18 18 Jazzy 1113 ATS I V . Y O U R J A Z Z Y 1 1 1 3 A T S Figure 3. Power Base Back View FRONT BATTERY BOX REAR BATTERY BOX BATTERY CONNECTORS SEAT POSTS MOTOR CONNECTORS Figure 4. Power Base Top View CHARGER HARNESS CONNECTOR 9-PIN CONTROLLER CONNECTOR AMMETER MAIN CIRCUIT BREAKER BATTERY CHARGER AC POWER RECEPTACLE SEAT POSTSPage 19 19 Jazzy 1113 ATS I V . Y O U R J A Z Z Y 1 1 1 3 A T S SEAT AND POWER BASE COMPONENTS The seating system and the power base consist of the following components. See figures 2,3,and 4.n Joystick/Controller: Used to move the power chair.n Armrests: Where arms can rest during time spent on the power chair.n Seat Release Plungers: Enable you to release the front of the seat from the seat posts.n Seat Frame: Where the seat attaches to the power base.n Freewheel Levers: Enable you to disengage the motor from the gearbox and push the power chair manually.n Body Shroud: The plastic pieces that cover the power base.n Footrest: Where feet rest during time spent on the power chair.n Anti-Tip Wheels: Wheels that allow “slight” or “no” tip while driving.n Drive Wheels: The main wheels that move the power chair.n Caster Wheels: The trailing wheels that provide stability.n Ammeter: Displays the charger’s current output in amps.n Main Circuit Breaker: The main circuit breaker is a safety feature built into your Jazzy 1113 ATS.When the batteries and the motors are heavily strained (e.g.,from excessive loads),the main circuit breaker trips to prevent damage to the motors and the electronics. If the circuit trips,allow the Jazzy to “rest” for approximately one minute. Then,push in the circuit breaker button,turn on the joystick controller,and continue normal operation. If the main circuit breaker continues to trip repeatedly,contact your authorized Pride provider.n 9-pin Controller Connector: Where the controller connects to the batteries,motors,and motor brakes.n Battery Charger AC Power Receptacle: Where the battery charger cord plugs in when the batteries need to be recharged.n Battery Connectors: Where the battery boxes connect and disconnect from the electronics tray.n Charger Harness Connector: Where the charger connects to the controller.Page 20 20 Jazzy 1113 ATS I V . Y O U R J A Z Z Y 1 1 1 3 A T S FREEWHEEL LEVERS For convenience,your Jazzy 1113 ATS is equipped with two freewheel levers—one for each motor. See figures 2 and 5. These levers allow you to disengage the drive motors from the gearboxes and maneuver the chair manually. This is called freewheel mode.WARNING: Do not use the Jazzy 1113 ATS without an attendant present while the drive motors are disengaged! Do not disengage the drive motors when your Jazzy 1113 ATS is on an incline,as the chair could roll down on its own and cause injury!To engage or disengage the drive motors: 1. Pull up the freewheel levers to disengage the drive motors and place your power chair in freewheel mode. See figure 5.2. Push down the freewheel levers to engage the drive motors and place your power chair in drive mode.NOTE: It is important to remember that when the Jazzy 1113 ATS is in the freewheel mode,the braking system is disengaged.ACTIVE-TRAC SYSTEM Your Jazzy is equipped with an Active-Trac System (ATS). ATS is a suspension system designed to make your Jazzy traverse different types of terrain and obstacles while maintaining smooth operation. With ATS,your front anti-tip wheels work in conjunction with your motor suspension to help you maneuver over obstacles.As your front anti-tip wheels come in contact with an obstacle,the front anti-tip wheel assembly is drawn upward. At the same time,your motors are forced downward. This allows the motors to push the Jazzy over an obstacle and limits the possibility of your power chair becoming “hung up” on the obstacle.ATS also helps in day-to-day operating conditions. For instance,when you release the joystick,your Jazzy begins to slow down. As the chair slows down,the front anti-tip wheels will automatically drop toward the ground. This will reduce the forward tip that is typically encountered with center-wheel drive chairs.Figure 5. Right Motor Freewheel Lever Figure 6. ATS System ATS SPRING FREEWHEEL LEVER IN FREEWHEEL MODEPage 21 21 Jazzy 1113 ATS V . D I S A S S E M B L Y FOOTREST SEAT RIGHT POWER BASE FRAME ASSEMBLY BATTERY BOXES BATTERY WELL FRAME FRONT FRAME Figure 7. The Jazzy 1113 ATS Component Assemblies The Jazzy 1113 ATS disassembles into eight easily transportable component assemblies—with no tools required. See figure 7.WARNING! Even though no tools are required to disassemble or assemble the Jazzy 1113 ATS,you should take care not to place your hands or fingers on the areas of the component assemblies where they may be pinched,as the assemblies “snap” together or “snap” apart.NOTE: During both the disassembly and the assembly of the Jazzy 1113 ATS,you may find it helpful to engage the Jazzy drive motors so that it does not roll while you are disassembling or assembling it. See IV.“Your Jazzy 1113 ATS.” DISASSEMBLY PREPARATION Position the Jazzy in a location where there is ample working room on all four sides of it. We recommend three or more feet of clearance on all sides. There are eight component assemblies,some of which take up a great deal of space when disassembled from the chair. Make certain that the Jazzy is powered off.LEFT POWER BASE FRAME ASSEMBLYPage 22 22 Jazzy 1113 ATS V . D I S A S S E M B L Y SLIDE FOOTREST UP AND PULL FORWARD TO REMOVE Figure 9. Removing the Footrest Figure 8. Removing the Seat Disconnect the controller and charger harnesses.1. Disconnect the controller connector and charger harnesses.See figure 3. You may need to pull firmly and gently wiggle the connectors to remove them from the socket. To disconnect the charger inhibit connector,you must squeeze the latch release levers.Remove the seat.1. Push in the seat release plungers (one on the front of each seat frame side tube) and lift up the seat. See figure 8.2. Allow it to rest on the front seat posts.3. Pull forward on the seat frame to release it from the rear seat posts. You may find it necessary to wiggle the frame gently from side to side to free the locating pins from their slots.WARNING! Do not pick up the seat frame by the armrests. They are free to pivot,and you may lose control of the seat if they do so,resulting in personal injury and/or damage to the chair.Remove the footrest.1. Slide the mounting bracket up the vertical bar of the front frame until the tabs on the mounting bracket can be pulled forward through the matching slots in the front frame. See figure 9.Remove the battery well frame.1. Disconnect both battery box and motor connectors. See figure 9.2. Lift and remove each battery box.3. Squeeze together the latch release levers that hang vertically down from the crossbar at the rear of the battery well frame.See figure 11. Lift up the rear end of the battery well frame.Pull it to the rear of the chair to release the front slots from the locating pins on the bottom bar of the front frame.Disassemble the Right/Left Frame Assembly from the Front Frame.1. Choose which side of the frame assembly (right/left) you want to disassemble first.2. After making your determination,stand behind the Jazzy and grasp the frame assembly handle on the side you wish to disassemble first (located next to the front seat post tower).See figure 12.Figure 10. Removing Battery Boxes SEAT RELEASE PLUNGERSPage 23 23 Jazzy 1113 ATS V . D I S A S S E M B L Y Figure 12. Removing Front Frame 3. Use your hand and thumb to hold the front frame and press and hold (toward the center of the front frame) the silver-colored latch release lever. See figure 12.4. Hold the frame assembly with one hand and push the frame assembly outward.5. Pull up on the front frame with your other hand until the latching mechanism releases.6. Keep pulling upward with your hand until the locating pin on the bottom of that side of the front frame releases from its slot in the frame assembly.7. Carefully let the frame assembly tilt to a resting position.Figure 11. Removing Battery WellPage 24 24 Jazzy 1113 ATS V I . C O M F O R T A D J U S T M E N T S After you have become familiar with your Jazzy’s operation,you may find the need to make adjustments to the Jazzy’s seat. There are some adjustments you can make to increase your comfort such as seat height and angle,armrest height and angle,the footrest height and angles,and the joystick position.CAUTION! If your Jazzy 1113 ATS was configured at your authorized Pride provider or service center,please consult your health care professional before changing seat position or making any other adjustment. Some of these adjustments may degrade your Jazzy’s performance and safety by changing its center of gravity.SEAT HEIGHT AND ANGLE You can change the seat height by either raising or lowering the four seat towers.To change the seat height: 1. Remove the seat.2. Remove the battery boxes.3. Remove the ball detent pin from each seat tower. See figure 13.4. Raise or lower each seat tower to the desired position.5. Install the ball detent pin into each seat tower.6. Reinstall the seat.To change the seat angle: You can change the seat angle by either raising or lowering only one set of seat towers (front or rear).Figure 13. Seat Post REMOVE BALL DETENT PIN TO CHANGE SEAT HEIGHT.Figure 14. Seat Adjustments ARMREST WIDTH ADJUSTMENT KNOBS REMOVE TO ADJUST SEATBACK ANGLE.Page 25 25 Jazzy 1113 ATS V I . C O M F O R T A D J U S T M E N T S SEAT BACK ANGLE ADJUSTMENT If your power chair is equipped with an adjustable seat back,you can adjust it to four (4) different angles,90°,102°,105°,or 107°.To adjust the backrest angle: 1. Use a hex key and a 3/8-in. wrench to remove the bolts on both seat hinges. See figure 14.2. Set at desired angle.3. Reinstall the bolts on both seat hinges and tighten.ARMREST WIDTH To change the armrest width: 1. Locate the two knobs on the armrest receiver bracket. See figure 14.2. Loosen the knobs and slide the armrests in or out to the desired width.3. Tighten the knobs.ARMREST ANGLE You can increase or decrease the armrest angle to fit your specific needs.See figure 15.To change the armrest angle: 1. Lift the armrest straight up so that it is perpendicular to the floor.2. Use a 7/16-in. wrench to loosen the jam nut. See figure 15.3. Use a 5/32-in. hex key to loosen the adjustment screw.4. Turn the screw clockwise to lower the front of the armrest and counterclockwise to raise the front of the armrest.5. Lock the adjustment screw into place by tightening the jam nut.JOYSTICK EXTENSION The joystick control can easily slide out away from the armrest,or in toward the armrest.To extend the joystick: 1. Use a 3/16-in. hex wrench to loosen the setscrew. See figure 16.2. Slide the joystick mounting bracket into or out of the armrest to the desired position.JOYSTICK POSITION You can position the joystick for either left-hand or right-hand use.To change the joystick position: 1. Disconnect the controller and charger harnesses. See figure 3.2. Cut the wire tie that attaches the controller cable to the armrest.3. Use a 3/16-in. hex key to loosen the setscrew. See figure 16.4. Slide the joystick mounting out of the armrest and place it in the other armrest.5. Tighten the setscrew.6. Connect the controller cable to the armrest with a wire tie. See figure 16.Figure 16. Underside of Armrest LOOSEN THIS SETSCREW TO ADJUST JOYSTICK.Figure 15. Armrest Angle Adjustment TURN THIS SCREW TO CHANGE ARMREST ANGLE.JAM NUT LOCKS ADJUSTMENT SCREW IN PLACE.Page 26 26 Jazzy 1113 ATS Figure 18. Footrest Adjustment FOOTREST HEIGHT ADJUSTMENT FOOTREST ANGLE ADJUSTMENT (SETSCREW LOCATED UNDERNEATH FOOTREST) Figure 17. Wire Tie Location USE A WIRE TIE TO SUPPORT THE CONTROLLER CABLE V I . C O M F O R T A D J U S T M E N T S FOOTREST HEIGHT The footrest height is easily adjusted to one of six different heights,in one-inch increments.To raise or lower the footrest: 1. Remove the cap screw,5/16-in. nut,and washers from the footrest. See figure 18.2. Raise or lower the footrest to the desired height.3. Reinstall the cap screw,nut,and two washers into the footrest and tighten.FOOTREST ANGLE You can adjust the angle of the footrest with a 3/16-in.hex key. See figure 18.To adjust the footrest angle: 1. Turn the setscrew clockwise to lower the front of the footrest.2. Turn the setscrew counterclockwise to raise the front of the footrest.3. Tighten the setscrew by turning it clockwise.Page 27 27 Jazzy 1113 ATS V I . C O M F O R T A D J U S T M E N T S ANTI-TIP WHEELS WARNING! Consult your Pride provider before attempting to change the anti-tip wheel height!Changing the anti-tip height affects handling under deceleration!The Jazzy 1113 ATS mid-wheel drive design provides superior performance and safety. The anti-tip wheels are an integral part of this design because they provide you with stability during deceleration. The anti-tip wheels are preset at the factory to a height of 3/4-in. off the ground. This is the ideal setting for most Jazzy 1113 ATS users. However,you may encounter situations where you may need to adjust the anti-tip wheels.For instance,if you drive your Jazzy on surfaces such as deep pile carpeting,you may notice that the anti- tip wheels have a tendency to drag on the carpet. In this case,you may need to raise the anti-tip wheels. If you drive your Jazzy primarily on smooth surfaces such as linoleum or tile,you may find that you tip forward more than is comfortable for you. (This may be more apparent for lighter users.) In this case,you may need to lower the anti-tip wheels. Adjusting the anti-tip wheels also affects the stiffness of the suspension.Raising the anti-tip wheels stiffen the suspension while lowering the anti-tip wheels soften the suspension.NOTE: Before making height adjustments on your anti-tips,consult your Pride provider to make sure that your seat is positioned properly. Moving your seat rearward one (1) inch may be sufficient.Anti-Tip wheel Adjustment You will need a 1/2-in. wrench and socket,a 5/32-in. hex key,and a 7/16-in. socket to adjust the anti-tip wheels.To adjust the anti-tips: 1. Make sure the power chair is in drive mode.2. Use the 5/32-in. hex key and the 7/16-in. socket to loosen the nut and bolt that fasten the anti-tip spring to the anti-tip arm. See figure 19.3. Use the 1/2-in. wrench and 1/2-in. socket to remove the anti-tip wheel.4. Use the 5/32-in. hex key and 7/16-in. socket to remove the anti-tip adjustment bolt.5. Raise or lower the anti-tip wheel in 1/4-in. increments.6. Replace the hardware into the appropriate hole and tighten.7. Install the anti-tip wheel.LOOSEN THIS BOLT REMOVE ANTI-TIP WHEEL Figure 19. Anti-Tip Adjustment REMOVE TO RAISE/LOWER ANTI-TIP.Page 28 28 Jazzy 1113 ATS Figure 20. Frame Assemblies Figure 21. Connecting Front Frame Assembly V I I . A S S E M B L Y Assemble the front frame and power base frame assemblies.1. Place the three frame assemblies next to each other as shown in figure 20.2. Grasp the front frame and fit the notch on the bottom bar of the front frame onto the locating pin on the lower section of the power base frame assembly. See figure 21.3. Pivot the front frame top bar toward the power base frame assembly and push the top bar of the front frame onto the locking mechanism until the two assemblies snap securely into place. See figure 22.4. Repeat for the other power base frame assembly.CAUTION! Make certain that the front frame is snapped securely to both the right frame assembly and to the left frame assembly.Install the battery well frame.1. Hold the battery well frame so that the bottom of the well hangs downward.2. Position the notches on the front of the battery well frame onto the locating pins on the bottom bar of the front frame. See figure 23.3. Fit the notch on either side of the rear of the battery well frame onto the locating pin on the power base frame assembly and onto the locating pin on the other power base frame assembly.4. Make certain that the locking mechanisms snap securely into place.Figure 22. Fitting the Frames Figure 23. Connecting Battery Well Frame LOCATING PINS LOCATING PINPage 29 29 Jazzy 1113 ATS V I I . A S S E M B L Y Install the battery boxes.1. Place the front battery box into the front end of the battery well frame.NOTE: Make certain that the battery box connectors are facing each other.2. Place the rear battery box into the back end of the battery well frame. Make certain that none of the wiring harnesses or cables are pinched between the battery or the motor controller box and the frame.3. Connect the battery boxes. Use the battery connection label for a reference.4. Reconnect the left and right motor connectors. Be certain to match the left connector to the left motor and the right connector to the right motor. The connectors are labeled left and right.Install the seat.1. Pick up the seat by the frame and slide the locating pins near the back of the frame into the matching slots on the left and rear seat post mounts.2. Slide the pins to the back of the slots. It may be necessary to wiggle the seat slightly from side to side to seat the pins firmly at the back of the slots.3. Push the front of the seat frame down until both the left and the right frame sides lock into the front seat post mounts.Install the footrest.1. Match the two tabs at the back of the footrest mounting bracket with the two semicircular notches in the vertical bar of the front frame.2. Push the tabs through the matching notches.3. Slide the footrest down into place.Connect the joystick/controller.1. Reconnect the controller and charger harnesses. See figure 3.CAUTION! Do not place the controller cable so that it can be pinched in the seat frame or the power base frame.Page 30 30 Jazzy 1113 ATS V I I I . O P E R A T I O N Figure 24. Joystick Movement BATTERY CONDITION METER ON/OFF BUTTON SPEED/ RESPONSE ADJUSTMENT KNOB Figure 24. Pilot Joystick Features PILOT CONTROLLER The standard controller on the Jazzy 1113 ATS is the Pilot. The Pilot controller is located directly underneath the joystick—on the seat arm. See figure 24. The Pilot controller is connected to the motors and batteries through two connectors on the back of the power base. See figure 3. You control the speed and direction of your Jazzy 1113 ATS by moving the joystick.To operate your Jazzy: 1. Turn it on (push the on/off button). The battery condition meter lights indicate the present charge of your battery.2. Push the joystick in the direction you wish to move. The farther you push the joystick from the neutral (center) position,the faster the Jazzy 1113 ATS moves.The controller translates the speed and directional information from the joystick for the motors. It has self-diagnostic features that are designed to search for potential problems at the rate of 100 times per second. If the controller detects a problem in the power chair’s electrical system,the power chair may,depending on the severity of the problem,stop functioning. (See “Trouble Codes.”) The controller is designed to maximize user safety under normal operating conditions. This controller,however,cannot take into account circumstances that put the Jazzy 1113 ATS outside of its normal operating environment as described within this manual. It is very important that you follow the precautions described within this manual.Joystick Functions The joystick controls the direction and speed of the power chair. When you move the joystick from the neutral (center) position,the electromagnetic brake releases and allows the power chair to move. The farther you push the joystick from its neutral position,the faster you can move the chair. When you release the joystick and allow it to return to the neutral position,you engage the electromagnetic brake. This causes the chair to decelerate and come to a complete stop.WARNING! Do not use the on/off button to stop the Jazzy 1113 ATS! This may cause injury.Speed and Response Adjustments The Pilot controller is equipped with a speed and response adjustment knob that helps you select the speed and response settings best suited to your requirements and environment. See figure 24. The knob controls the speed at which your Jazzy 1113 ATS responds to joystick movement. When this knob is turned completely counterclockwise,the forward and reverse acceleration and braking are slowed substantially. When this knob is turned fully clockwise,the Jazzy 1113 ATS speed increases to its maximum.JOYSTICKPage 31 31 Jazzy 1113 ATS V I I I . O P E R A T I O N NOTE: We recommend that the first few times you operate your Jazzy 1113 ATS,you turn the speed/ response adjustment knob completely counterclockwise to allow you to become familiar with your new Jazzy 1113 ATS.Battery Condition Meter The battery condition meter is located immediately in front of the joystick. This enables you to monitor battery life. The battery condition meter indicates the approximate amount of battery life left. See figure 24.n Red,yellow,and green bars indicate that the batteries are fully charged.n Red and yellow bars indicate that you should charge the battery if possible.n Red bars indicate that you should charge the battery as soon as possible,because low battery voltage may cause the chair to become inoperative.NOTE: When the batteries begin to approach a discharged state,the first red bar will begin to slowly flash,reminding you the batteries need to be charged immediately!Trouble Codes In addition to indicating the current state of battery charge,the battery condition meter can also indicate possible problems with your Jazzy 1113 ATS. If the battery condition meter lights are flashing rapidly,the controller may be indicating a fault.The meter itself has ten individual bars. The bars are meant to provide information by the amount of bars that are flashing. For instance,the very first red bar flashing rapidly indicates that the battery voltage is nearly depleted. The following is a list of the possible errors signified by the rapidly flashing meter lights.If you cannot resolve your problem,see an authorized Pride provider.FLASHING BARS DIAGNOSIS SOLUTION 10 High Battery Voltage Check Batteries 9Solenoid Brake Fault Check Motor/Brake Wiring 8Possible Controller Fault See Authorized Provider Service Center 7Possible Joystick Fault See Authorized Provider Service Center 6Inhibit Active Unplug Charger/Check Connections 5Right Motor Wiring Fault Check Right Motor Wiring 4Right Motor Disconnected Check Right Motor Wiring 3Left Motor Wiring Fault Check Left Motor Wiring 2Left Motor Disconnected Check Left Motor Wiring 1Low Battery Voltage Check Batteries/Battery Wiring Thermal Rollback The Pilot controller is equipped with a thermal rollback circuit. This circuit monitors the temperature of the motors and the controller. In the event that the motors or controller become excessively hot (above 122° F/ 50° C),the controller reduces the motor voltage. For every degree above 122° F/50° C,the controller reduces the voltage by 5 volts. This reduces your speed and allows the components to cool down. When the temperature returns to a safe level,your Jazzy 1113 ATS resumes its normal speed.Programming Your power chair is equipped with a programmable controller. Changes to the programming can only be made by your authorized Pride provider using special equipment. Changing the controller’s program will alter your power chair’s performance.Page 32 32 Jazzy 1113 ATS I X . B A T T E R I E S A N D C H A R G I N G Batteries Your Jazzy 1113 ATS uses two long-lasting,12-volt,deep cycle batteries. These batteries are sealed and maintenance free. Since they are sealed,there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a deep discharge. Though they are similar in appearance to automotive batteries,they are not interchangeable. Automotive batteries are not designed to handle a long,deep discharge,and are also unsafe for use in power chairs.CHARGING YOUR BATTERIES The battery charger is one of the most important parts of your Jazzy 1113 ATS. The battery charger is designed to optimize your Jazzy 1113 ATS’s performance by charging the batteries safely,quickly,and easily. The charging system consists of the charger,the charger fuse,and the ammeter. The onboard charger is located inside the rear battery case. The ammeter and charger fuse are located on the back battery case.The ammeter indicates the rate of charge necessary to fully recharge the batteries. It is also a good indication of whether or not the charger is working. The ammeter and the charger are only functional when the charger power cord is plugged into a wall outlet.WARNING! You must recharge your Jazzy 1113 ATS’s batteries with the supplied onboard or off- board charging system. Do not use an automotive-type battery charger.WARNING! Never use an extension cord to plug in your battery charger. Plug the charger directly into a properly wired standard wall outlet.To charge the batteries by using the onboard charger: 1. Position the rear of your Jazzy 1113 ATS close to a standard wall outlet.2. Be certain that the controller power is turned off and the freewheel levers are in the engaged position.See IV. “Your Jazzy 1113 ATS” in this manual.3. Extend the charger power cord and plug it into the wall outlet. The Jazzy 1113 ATS incorporates an inhibit function that disables the power chair when the charger is plugged into a wall outlet.4. The ammeter indicates how much charge is needed to fully charge the batteries. Wait about a minute for the charger to warm up. The ammeter may move up to as high as 5.5 amps,then gradually move back down to 0 amps as it charges.5. We recommend you charge the batteries for 8 to 14 hours. As the batteries charge,the ammeter needle will slowly drop to zero. When the batteries are fully charged,the needle will vibrate on or about the zero mark on the meter scale.6. When your Jazzy 1113 ATS’s batteries are fully charged,unplug the power cord from the wall outlet,wind it up,and store it in the seat pouch located on the back of the seat.Off-board Charger Your Jazzy may be equipped with an off-board,or external,charger. Typically,external chargers plug into the joystick controller. If your Jazzy is equipped with an external charger,refer to the instructions that come with the charger.WARNING! Battery posts,terminals and related accessories contain lead and lead compounds.Wash hands after handling.Page 33 33 Jazzy 1113 ATS I X . B A T T E R I E S A N D C H A R G I N G BATTERY BREAK-IN To break in your Jazzy’s new batteries for maximum efficiency: 1. Fully recharge any new battery prior to initial use. This will bring the battery up to about 90% of its peak performance level.2. Run your Jazzy 1113 ATS about the house and yard. Move slowly at first,and do not stray too far until you become accustomed to the controls and break in the batteries.3. Give the batteries another full charge of 8 to 14 hours and run the Jazzy 1113 ATS again. The batteries should now perform at over 90% of their potential.4. After four or five charging cycles,the batteries will top off at 100% charge and last for an extended period.BATTERIES AND CHARGING—FREQUENTLY ASKED QUESTIONS (FAQS) How does the charger work?The battery charger takes the standard wall outlet voltage of 120VAC (alternating current) and converts it to 28VDC (direct current). When the battery voltage is low,the charger works harder to charge the batteries.This is why the charging ammeter initially reads 5.5 or more amps. As the battery voltage approaches a full charge,the charger doesn’t work as hard to complete the charging cycle. This explains why the amperage on the charging ammeter drops as the batteries approach a full charge. When the batteries are fully charged,the amperage from the charger is nearly zero. This is how the charger maintains a charge but does not overcharge the battery. Your Jazzy 1113 ATS’s charger will not be able to charge your batteries after the batteries have been discharged to nearly zero voltage. If this happens,call your authorized provider for assistance.Can I use a different battery charger?You should use the charger supplied with the Jazzy 1113 ATS. It is the safest,most efficient tool to charge the batteries. We do not recommend using other types of chargers (e.g.,an automotive battery charger).How often must I charge the batteries?Many factors come into play when deciding how often to charge the batteries. You may use your Jazzy 1113 ATS all day on a daily basis,or you may not use it for weeks at a time.n Daily Use If you use your Jazzy 1113 ATS on a daily basis,charge the batteries as soon as you are finished using it for the day. Then,your Jazzy 1113 ATS will be ready each morning to give you a full day’s service.We recommend that you charge the batteries 8 to 14 hours after daily use. Do not charge the batteries for more than 24 hours.n Infrequent Use If you use your Jazzy 1113 ATS infrequently (once a week or less),you should charge it at least once per week for 12 to 14 hours.NOTE: Keep the batteries fully charged and avoid deeply discharging the batteries. Do not charge the batteries for more than 24 hours.Page 34 34 Jazzy 1113 ATS I X . B A T T E R I E S A N D C H A R G I N G How can I get maximum range or distance per charge?Rarely do you have an ideal driving situation such as smooth,flat,hard terrain with no hills or curves. More often you are presented with hills,sidewalk cracks,uneven and loosely packed surfaces,and curves. All of these factors affect the distance or running time per battery charge. The following are a few suggestions for obtaining the maximum range per charge: n Always charge the batteries fully prior to your trip.n Maintain 30-35 psi in pneumatic drive tires.n Plan your trip in advance to avoid inclines if possible.n Limit the baggage weight to essential items.What type of battery should I use?We recommend deep-cycle batteries that are sealed and maintenance free. Both sealed lead-acid (SLA) and gel cell are deep-cycle batteries and are similar in performance.Use these specifications to reorder deep-cycle batteries.Battery Specifications Type: Deep-Cycle sealed lead-acid or gel cell Size: U1 Voltage: 12 volts each Amp Hours: 35 amp hours Why do my new batteries seem weak?Deep-cycle batteries employ a different chemical technology than those used in car batteries,nickel-cadmium (nicads),or in other common battery types. Deep-cycle batteries are specifically designed to provide power,drain down their charge,and then accept a relatively quick recharge. Lead acid batteries should be charged as often as possible. They do not have a “memory” like nickel-cadmium batteries.We work closely with our battery manufacturer to provide a battery that best suits the Jazzy 1113 ATS’s specific demands. Fresh batteries arrive regularly and are promptly shipped with a full charge. During shipping,the batteries encounter temperature extremes that may influence their initial performance. Heat robs the charge from the battery,and cold slows the power available and extends the time needed to recharge the battery (just as with a car battery).It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature. More importantly,it takes a few “charging cycles” (a partial drain,then a full recharge) to establish the critical chemical balance that is essential to the battery’s peak performance and long life. It is well worth it for you to take the time to break in the batteries properly.NOTE: The useful life of a battery is quite often a reflection of the care it receives.Page 35 35 Jazzy 1113 ATS I X . B A T T E R I E S A N D C H A R G I N G How can I ensure maximum battery life?A fully charged deep-cycle battery provides reliable performance and extended battery life. Keep your Jazzy’s batteries fully charged whenever possible. Batteries that are regularly and deeply discharged,infrequently charged,or stored without a full charge may be permanently damaged,causing unreliable Jazzy operation and limited battery life.How should I store my Jazzy 1113 ATS and batteries?If you do not use your Jazzy 1113 ATS regularly,we recommend maintaining battery vitality by charging the batteries at least once a week.If you do not plan on using your Jazzy 1113 ATS for an extended period,fully charge the batteries prior to storage. Disconnect the battery harnesses and store the Jazzy in a warm,dry environment. Avoid temperature extremes such as freezing conditions and excessively hot conditions,and never attempt to charge a frozen battery. A cold or frozen battery should be warmed for several days prior to recharging.NOTE: If you are storing a Jazzy 1113 ATS for an extended period of time,you may wish to block the unit up off the ground with several boards under the frame. This keeps the tires off the ground and prevents the possibility of flat spots developing.What about public transportation?If you intend to use public transportation while using your Jazzy,you must contact in advance the transportation provider to determine their specific requirements. See II. “Safety” for more details.Sealed lead-acid and Gel Cell batteries are designed for application in power chairs and in other mobility vehicles. Generally,sealed lead-acid batteries are safe for all forms of transportation such as aircraft,buses,and trains. We suggest that you contact your transportation provider to determine specific requirements of transportation and packaging.What about shipping?If you wish to use a freight company to ship the Jazzy 1113 ATS to your final destination,repack the Jazzy 1113 ATS in the original shipping cont


The Pride Jazzy is the Power Chair designed with real life and the lifestyles of our clients,in mind. Here at Pride we understand what that means and that’s why the Jazzy is designed to be the perfect blend of performance,style,and personal expression.




3 wheel electric scooter, 4 wheel electric scooter, electric lift chair, electric mobility, electric mobility scooter, electric scooter, jazzy, jazzy electric wheel chair, jazzy power chair, jazzy power wheel chair, jazzy wheel chair, lift chair, medical lift chair, medical walker, medical supply walker, mobility, mobility product, mobility scooter, motorized lift chair, power chair, power lift chair, pride electric scooter, pride jazzy, pride lift chair, pride mobility, pride scooter, transport chair, walkers, wheel chair transport, wheeled chair